CNC Spindle Motor Air Cooled 1.5KW Kit
Product Description
Neotronics SA has been in the CNC Laser industry for over 7 years. With unmatched support and price, We are one of the largest CNC stores in South Africa. Join the Neotronics experience!
We supply high quality spindle motors at affordable prices.
This is the CNC Spindle Motor Air Cooled 1.5KW Kit. It comes with an Inverter, 80mm clamp, and 11 ER16 Collets. Should you need a complete wiring diagram and connection instructions please contact us.
Big Advantages of our spindle motors:
- P4 fully sealed angular contact bearings,2×7004C P4 DT &2×7002C P4 DT, increase spindle life.
- Longer lengths make the torque bigger, and more powerful.
- Careful assembly makes the spindle more precisional.
- Precision 0.01mm.Coaxial degree less than 0.0025mm
Important Tips
- Spindle in the preservation and transportation, high-speed grease inside the bearing state will change, customers should be running at low speed for 30 minutes. 3000 rpm and then follow the slow increase, running for 20 minutes. The spindle and the inverter should be working together. The inverter's specifications and parameter settings need to match the spindle parameter. (Because of high-speed grease inside the bearing state will change, when you get the spindle, maybe the noise sounds not normal. Please run it for 20 minutes to warm up.
- Connect the inverter spindle, the three-phase inverter power cord should be soldered in the plug 1 (U), 2 (V), 3 (W) feet, and 4 feet for the ground. After the power is turned on, observe whether the spindle rotation axis indicates the direction consistent. If inconsistency should be immediately shut down, replace the inverter and spindle-connected two wires of the three-phase power supply.
- During normal operation, air-cooled spindles often encounter some heat, always check whether the air-cooled spindle housing and duct clogging dust. If clogging dust, promptly clean it.
- Every day before using the spindle, run at low speed for 15-20 minutes. Clamping the cutters to the spindle, collet nuts, collets, and cutters must be clean enough. The Shank inserted into the collet must be greater than 15mm.
Product Specs:
- Size:80x198mm ( Body diameter:80mm; Length:198mm)
- Speed Ways: Through 3-phase output inverter and adjust the inverter frequency to change the spindle speed.
- Cooling: Air cooling
- Power Interface: Optional KC20-4 pins waterproof air plug. The air plug marked "1 ","2"," 3"," 4", "1 ","2 ","3" were connected to the inverter (U, V, W), and 4 connected inverter ground. (Pay attention! our spindle "4" connecting to GND, promised personal safety!!)
- Power:1.5kw
- Voltage:220vA
- Current:6A
- Frequency:0-400Hz
- Speed:0-24000rpm
- Runout Off: 0.01mm
- Diameter(mm): 80mm
- Bearing Type: 2X7004C P4 DT and 2X7002C P4 DT
- Full sealed angular contact bearings
- Collet: ER16
- Clip Knifediameter:10mm,9mm,8mm,7mm,6.35mm,6mm,5mm,4mm,3.175mm,3mm,2mm,1mm
- Air Cooling ER16 collet chunk
- Grease Lubrication
- Main Application: Engrave / Cut for wood, bamboo, normal PCB, PVC, PMMA,plastic, duotone board(ABS)and etc nonmetal, also can engrave on gold, silver,copper, aluminium,Pb etc soft metal surface working.
VFD Specs
Please note: Locally Stocked, Available for Immediate Shipping.